Beckers Corporation’s policy of quality and durability in the manufacture of its painted roofing and siding products, Hixwood Super Rib 100 is represented by this Limited Warranty. This Limited Warranty is valid for a period of 40 years on sidewalls and 35 years on roof panels.


  1. During the terms of this Warranty, the painted panel will not perforate or fail structurally due to deterioration from red rust.
  2. The paint will not.
    1. Crack, check, or peel (lose adhesion) for 40 years on sidewalls and 35 years on roof panels.
    2. Chalk in excess of a numerical rating of 7 when measured with the standard procedure specified in ASTM 04214-89, Method D659 on sidewalls for a period of 40 years.
    3. Chalk in excess of a numerical rating of 11 when measured with the standard procedure specified in ASTM D4214-89, Method D659 on roof panels for a period of 35 years.
    4. Fade or change color more than 6 units of color for sidewall panels in accordance with standard procedure of ASTM D2244-93 for a period of 40 years.
    5. Fade or change color more than 11 units of color for roof panels in accordance with standard procedure of ASTM D2244-93 for a period of 35 years.
  3. All products will conform to the performance certification of THE SYSTEM published by the company at the time of the sale.


  1. This Warranty is extended to the original buyer only and is not transferable or assignable.
  2. Abnormal atmospheric conditions to which this Warranty does not apply include, but are not limited to
    hail, exposure to corrosive or harmful chemicals (weather solids, liquids, or gases) airborne contaminants,
    animal wastes, exposure to salt water spray, decaying materials, wet absorptive material, and internal contamination created by improper ventilation or improper housekeeping. The Warranty does not cover damage caused by acts of God, falling objects, external forces, explosions, fire, riots, civil commotion, act
    of war, excessive radiations or other such similar or dissimilar occurrences beyond our control.
  3. This Warranty does not cover damages to the product’s finish caused by handling, shipping, transit, processing, storage or installation.
  4. This Warranty does not cover failures resulting from edge corrosion.


  1. The Buyer shall inspect material received from Beckers Corporation prior to installation so as to mitigate expenses involved in repairing, replacing, or repainting defective sheets. The Buyer accepts responsibility upon receipt of the material in the conditions described in paragraph 3 of Limitations on Warranty.
  2. Any claim on account of a defect in the products or for any other cause shall be deemed waive by buyer unless written notice thereof is given to Seller within 30 days after discovery of the defect and within the applicant warranty period. Buyer must submit proof of purchase in the event of such claim. Seller shall be given reasonable opportunity to investigate all claims.


If any of our products fail to perform as warranted, the company will, at its own option, repaint or replace the defective panels or refund the buyer the price paid for the material. The company’s total liability is expressly limited to the purchase price of the defective material. Except as provided herein the company shall not be liable for any losses, damage, or expense, whether direct, incidental or consequential, caused by or resulting from the use of defective or non-conforming products.




Beckers Corporation, extends this warranty to panels, effective from the date of shipment and sold as a warranted or Number One panels as indicated on the customer’s original invoice. It applies only to goods used on wood frame buildings and on architectural, commercial, pre-engineered or residential metal buildings, which are installed in the United States, Canada, and Mexico. This warranty shall extend to the purchaser of the material and is non-assignable and/or non-transferable. Should the purchaser become insolvent, bankrupt, make an assignment for the benefits of its creditors, or for any reason discontinue its normal or regular business practices, this warranty shall for with become null and void and of no legal effect. The purchaser must present the original sales receipt for warranty consideration.


Although it is recognized by Beckers Corporation, that most coatings, including BECKRYTECH®, will fade and change in appearance to some degree over a period of time in outdoor installations, and that such changes may not be uniform between surfaces and not equally exposed, Beckers Corporation, warrants that the goods covered by this warranty will resist natural weathering to the extent that they will conform to the performance standards below during a period of 40 years for film integrity and a period of 30 years after shipment for both chalking and color change, provided that all conditions of this warranty are first met. Provisions (1) through (3) below apply to buildings installed north of the 15 parallel of latitude in the northern hemisphere. Only provision (1) applies to buildings south of this latitude.

  1. For forty (40) years, BeckryTech® will not peel, flake, or otherwise lose adhesion to an extent that is apparent on ordinary outdoor visual observation. Note: Slight cracking may occur on roll-formed edges or break bends at the time of forming, and is considered as standard, such cracking shall not constitute a basis for complaint under this limited warranty; and
  2. For thirty-five (35) years, BeckryTech® will not chalk in excess of a numerical rating of seven (7-vertical installations),(5-non-vertical installations) when measured in accordance with the standard procedures in ASTM D-659 and NCCA 111-8; and
  3. For thirty-five (35) years, BeckryTech® will not, fade or change in color in excess of five (5) NBS units (vertical installations), or seven (7) NBS units (non-vertical installations) following installation. Color Measurements are to be made per ASTM D-2244 and only on clean surfaces after removing surface deposits and chalk per ASTM 3964.


This is an anti-weathering limited warranty and does not apply to other causes of degradation, including:

  1. BeckryTech® which has suffered scratching or abrasion or impact by a hard object; has been abused, altered, modified, used in a manner not originally intended or stored contrary to instructions of Beckers Corporation, or in accordance with good industry practice; is damaged due to moisture entrapment in bundles during transit or storage; is stored or installed in a way which allows standing water on the coating or in any chemically aggressive environment containing fumes, ash, cement dust, carbon black, salts, or other chemicals whether naturally occurring or caused by man; is stored or installed in a way which allows contact with animals and/or animal waste or its decomposition products; is stored or installed in an area, or in such a way, that damage can occur due to poor air circulation; caused by acts of God, radiation, falling objects, explosion, fire, riots, civil commotions, acts of war, or other external forces;
  2. BeckryTech® which suffers from improper forming, fabrication, or embossing; cut edge exposure; corrosion of the substrate; or the development of any other condition between the coating and the substrate which causes the coating to degrade or delaminate, including any failure or deficiency in the cleaning process or pretreatment;
  3. BeckryTech® which is installed within 1000 meters of salt water or other marine environment;
  4. This warranty will not extend to or cover damages to the material due to improper shipping, handling, installation, storing, erecting of the panels on the job site and/or any act of negligence of the customer or any third party after the panels leave the possession of Beckers Corporation. Claims arising from the following conditions will also not be warranted; a) Steel shavings from sawing sparks that come into contact with the paint surface. B) Damage to the paint surface due to the use of an abrasive saw blade. C) Panels used on or near animal confinement. D) Damage due to the use of wet, green. or treated lumber. E) Use of fasteners not recommended by Beckers Corporation.


If any of the products fails to perform as warranted, the company will repaint or replace the defective panels at its sole discretion, and Beckers Corporation, shall bear no liability, except to the options listed above. If Beckers Corporation, chooses to replace the defective material, the liability is expressly limited to the purchase price of the defective material, and labor costs will not be given due consideration. Beckers Corporation, will not be held responsible for any losses, damages, or expenses caused by or resulting from the use of defective material. Beckers Corporation, reserves the right to terminate or modify this warranty except with respect to orders already accepted.

2526 Delta Lane, Elk Grove Village, Illinois 60007 Telephone (847)-766-3555 Fax (847)-766-3595
15310 Arrow Boulevard, Fontana, California 92335 Telephone (909)-356-1095 Fax (909)-356-0854

Visualize Your Building

Use our tool to pick the building and colors that will make it yours.

Visualizer Tool »

"Hixwood Metal has continuously delivered high quality products in a very timely manner, allowing me to focus on running the business and getting more contracts."

Gingerich and Sons Construction

Ready to Get Your Project Started?